Shop

Sonic Sentry Alarm

Part Number: SSA474
Title: SONIC SENTRY ALARM
Category: CCTV
Industry: CCTV/Security,

The SSA474 SONIC SENTRY ALARM is a four channel audio detection system used to detect the sound caused by movement of any person or object in the monitored area. All movement or contact with surfaces produce sound waves in the air that are received by a local microphone in the monitored area and sent to the SONIC SENTRY ALARM unit by wire.

SKU: 7381aa30d2ff Categories: , Tags: ,

Description

Click here to download the manual in Word 6.0 format. Download Manual
Click here to download the manual in Word 6.0 format. Download “Sound to Improve Security” Article

Part Number: SSA474
Title: SONIC SENTRY ALARM
Category: CCTV
Industry: CCTV/Security,

Description:

The SSA474 SONIC SENTRY ALARM is a four channel audio detection system used to detect the sound caused by movement of any person or object in the monitored area. All movement or contact with surfaces produce sound waves in the air that are received by a local microphone in the monitored area and sent to the SONIC SENTRY ALARM unit by wire. Many video cameras have built in microphones that can be used to provide a higher level of security with this unit. The unit electronically listens to the audio signal and determines when to close an alarm contact. This alarm contact is Normally Open or Normally Closed and can be used to alert local monitor personnel or activate other alarm equipment. Connect it to a multiplexer and switch the video source to a higher scan rate when an alarm is being received from that area. This will improve picture motion quality on that camera when action is occurring. A built in audio gain control keeps ambient audio below alarm detection level while maximizing the sensitivity of the alarm trigger level. This allows the system to have maximum sensitivity and operate in relatively noisy environments. Equipment such as air conditioners, fans, and heaters operating in the monitored area will not trigger the alarm. Slowly changing sounds such as aircraft flying over the building or cars driving by the outside of the building can be ignored by the alarm while still having a very sensitive trigger to sounds inside the monitor area. The Sonic Sentry Alarm uses audio to detect motion without violating the privacy of any person in the monitor area since no one is listening to or recording the audio. This provides Protection without Intrusion of Privacy. If monitoring or recording of the audio is desired, the audio signal is available at the rear RCA connectors. There is an RCA connector for each of the four audio channels and one RCA connector that is switched to any channel that is in alarm at the time. This is used when only a single channel of audio may be recorded. Audio will only be recorded if an audio patch cable is connected between the SSA474 and the audio input of the recorder. The audio detect sensitivity is adjustable from the front panel. Adjust the sensitivity control during normal sound level in the monitor area until the alarm LED goes out and that’s it, the unit is ready to detect unwanted intrusions. SSA474 SONIC SENTRY ALARM INPUT SPECIFICATIONS Audio Channels 4 Independent Audio Interface Microphone or Line Level Microphone Phantom Power +5 VDC Selectable Input Level -50 dBm to 0 dBm Microphone Impedance Balanced Hi-Z Common Mode Suppression 40dB Minimum Connectors Wire Screw Terminal CONTROL SYSTEM Alarm Sensitivity Adjustable (Front Panel) Frequency Response 100 Hz to 15 KHz Control Range 50 dB AGC range Distortion 0.1 %THD maximum Signal-To-Noise 70 dB @ 0 dBm OUTPUT Audio Level 0 dBm Impedance Low-Z Connectors RCA (female) Switched Output Audio with Dwell (Time Delay) Switch Dwell 1, 3, & 10 Second (Selectable) RELAY OUTPUT Relay Form C NO, NC, Selectable Connectors Wire Screw Terminal METERING Alarm Indicator Red Alarm L.E.D. MECHANICAL Card Fits in one of nine spaces in the RMS-400 Mainframe Power Requirement +/-12 VDC (RMS-400) NOTE: A microphone is required for each channel. If your camera does not have a built-in microphone you can purchase the matching microphones. The part number is SSA-MIC, four SSA-MIC microphones are required for each SSA474 card.

If this product page shows “out of stock” the product is in production and can be purchased with a lead time of 1-2 weeks or less depending on quantity. To place an order for this product call 1-800-235-6960 and ask for the sales department. Or E-Mail your order to fmsystemsinc@sbcglobal.net. Most orders ship within a few days.